Wilo-CronoBloc-BL-E

00588001_0

Design

Electronically controlled glanded single pump in monobloc design with flange connection and automatic power adjustment.

Application

Pumping of heating water (acc. to VDI 2035), cold water and water/glycol mixtures without abrasive substances in heating, cold water and cooling systems.

Type key

Example BL-E 40/160-5.5/2-R1
BL-E Monobloc pump with electronic control
40 Nominal diameter DN of the pipe connection (pressure port)
160 Nominal impeller diameter in mm
5.5 Rated motor power P2 in kW
2 Number of poles
-R1 Version without differential pressure sensor

Special features/product advantages

  • Energy savings due to integrated electronic control
  • Optional interfaces for bus communication using plug-in IF-Modules
  • Simple operation due to tried-and-tested red-button technology and display
  • Integrated full motor protection (PTC thermistor sensor) with trip electronics
  • Meets user requirements due to performance and main dimensions in accordance with EN 733 (DIN for norm pumps)

Technical data

  • Minimum Efficiency Index (MEI) ≥ 0.4
  • Permissible temperature range of -20 °C to +140 °C
  • Mains connection
    • 3~440 V -5/±10 %, 50/60 Hz
    • 3~400 V ±10 %, 50/60 Hz
    • 3~380 V -5/±10 %, 50/60 Hz
  • Protection class IP 55
  • Nominal diameter DN 32 to DN 125
  • Max. operating pressure 16 bar (120 °C)
00665677_0

Description/design

Single-stage low-pressure centrifugal pump in block design, with axial suction port and radially arranged pressure port with

  • Mechanical seal
  • Flange connection with pressure measuring connection R 1/8
  • Lantern
  • Coupling
  • Drive with integrated electronic speed control

Materials

  • Pump housing and lantern: Standard: EN-GJL-250; optional: Spheroidal cast iron EN-GJS-400-18-LT
  • Impeller: Standard: EN-GJL-200; optional: Bronze CuSn 10
  • Shaft: 1.4122
  • Mechanical seal: AQEGG other mechanical seals on request

Operating modes

  • Δp-c for constant differential pressure (only with external DDG)
  • PID control
  • Control mode (n=constant)

Manual operation level

  • Red button and display

Manual functions

  • Differential pressure setpoint setting
  • Setting the speed (manual control mode)
  • Setting the operating mode
  • Setting the pump ON/OFF
  • Configuration of all operating parameters
  • Error acknowledgement

External control functions

  • “Overriding Off” control input
  • Analogue input 0-10 V, 0-20 mA for manual control mode (DDC) and remote setpoint adjustment
  • Analogue input 2-10 V, 4-20 mA for manual control mode (DDC) and remote setpoint adjustment
  • Analogue input 0-10 V for actual value signal from pressure sensor
  • Analogue input 2-10 V, 0-20 mA, 4-20 mA for actual value signal from pressure sensor

Signal and display functions

  • Collective fault signal SSM
  • Collective run signal SBM

Data exchange

  • Infrared interface for wireless data exchange with IR-Monitor/IR-Stick
  • Plug-in position for Wilo IF-Modules (Modbus, BACnet, CAN, PLR, LON) for connection to building automation

Safety functions

  • Full motor protection with integrated trip electronics
  • Access disable

Dual pump management (2 x single pump; Y-pipe application only)

  • Main/standby operation (automatic fault-actuated switchover)
  • Pump cycling main/standby operation after 24 hours
  • Parallel operation

Scope of delivery

  • Pump
  • Installation and operating instructions

Options

  • …-L1 variant with bronze impeller (at additional charge)
  • …-H1 variant with housing made of spheroidal cast iron (at additional charge)
  • …-S1/-S2 variant with special mechanical shaft seal (at additional charge)

Accessories

  • Brackets with fixation material for installation on a base
  • IR-Monitor, Wilo-IR-Stick
  • IF-Module PLR for connecting to PLR/interface converter
  • IF-Module LON for connection to the LONWORKS network
  • IF-Module BACnet
  • IF-Module Modbus
  • CAN IF-Module
  • Control system VR-HVAC
  • Control system CCe-HVAC
  • Control system SCe-HVAC
  • Differential pressure sensor (DDG)

General notes - ErP (ecological design-) directive

  • The benchmark for most efficient water pumps is MEI ≥ 0.70
  • The efficiency of a pump with a trimmed impeller is usually lower than that of a pump with the full impeller diameter. The trimming of the impeller will adapt the pump to a fixed duty point, leading to reduced energy consumption. The minimum efficiency index (MEI) is based on the full impeller diameter.
  • The operation of this water pump with variable duty points may be more efficient and economic when controlled, for example, by the use of a variable speed drive that matches the pump duty to the system.
  • Information on benchmark efficiency is available atwww.europump.org/efficiencycharts
  • Pumps with power consumption > 150 kW or a volume flow QBEP < 6 m3/h are not subject to the Ecodesign Directive for water pumps. Therefore, no MEI value is shown.